MECHANICAL
Standard Crystal Vision module 266mm x 100mm
Weight (with two piggyback modules fitted): 260g
Power consumption: 12 Watts
VIDEO INPUT
One HD or SD input
270Mb/s or 1.5Gb/s serial compliant to EBU 3267-E, SMPTE 259M and SMPTE 292M
The video formats supported are 625, 525, 720p50, 720p59.94, 720p60, 1080i50, 1080i59.94, 1080i60, 1080PsF23.98 and 1080PsF24
HD cable equalisation up to 140m with Belden 1694 or equivalent (approx. 100m with Belden 8281). SD cable equalisation >200m Belden 8281 or equivalent
Input return loss: -15dB for 50MHz to 1.5GHz
Automatic de-embedding to SMPTE 272M or SMPTE 299M
VIDEO OUTPUTS
Two HD or SD outputs using RM33 or RM39 frame rear modules
Serial output: 270Mb/s or 1.5Gb/s serial compliant to EBU 3267-E, SMPTE 259M and SMPTE 292M
Output follows the input format
Audio is embedded to SMPTE 272M or SMPTE 299M
AUDIO INPUTS AND OUTPUTS
Piggybacks can be added to the main board to enable either input or output of 2 x AES or 2 x analogue stereo pairs. Fit one piggyback for one audio group or two piggybacks for two audio groups
Use HD-AIP2, HD-DIP2 or HD-DIP2-RS to input analogue, synchronous AES or asynchronous AES audio
Use HD-AOP2, HD-DOP2-75 or HD-DOP2-110 to output analogue, 75 ohm AES or 110 ohm AES audio
EMBEDDER TIMING PERFORMANCE
Interchannel: <1 clock cycle
Audio to video: embed and de-embed delays approximately 800us in SD and 90us in HD
De-embedder automatically handles asynchronous and synchronous audio
MONITORING
One miniature front mounted audio jack and switch selects individual stereo audio analogue monitoring on both embedder and de-embedder
EDH
EDH insertion on SD output
DOLBY E
Dolby E signals can be processed and routed without corruption
VIDEO DELAY
Optional one frame video delay (33.3ms or 40ms) for Dolby E compensation
AUDIO DELAY
Adjustable audio delay of up to 64ms on each channel. Delay is either on or off for any given channel
Presetable and controllable via the card, frame active front panel, remote panel and Statesman
DELAY THROUGH BOARD
Less than one line
AUDIO REPLACE
Routing of input piggyback audio together with audio or Dolby E from up to two de-embedded groups present on video input to any channel of up to two output embedder groups
AUDIO PROCESSING
Gain level adjustment on each channel between +18dB and -18dB in 0.1dB steps with 0dB calibration
Mute
Stereo to mono conversion
AUDIO PROTECTION IN DE-EMBEDDERS
Full support for data recovery using SMPTE 299M error correction codes
A variety of sophisticated techniques are employed to protect and minimise the effects of cuts to untimed and asynchronous SDI
LED INDICATION OF:
Power supplies on board
HD input present
SD input present
GPI error output (alarm) active
Audio levels calibrated
GPI INPUT LEVELS
Active pull to ground, pulled up to +5V through 10 kohm
GPI OUTPUT LEVELS
Electrically: Open collector transistors 30V, 270 ohm current limit resistors. Pulled up to +5V through 6800 ohm
GPI INPUTS
Four GPI inputs can be used to recall stored presets
GPI OUTPUTS
Two GPI outputs have programmable alarm outputs
LOCAL CONTROL
Intuitive board edge interface with two select buttons, shaft encoder and 10 character alphanumeric display
All functions available from board edge
REMOTE CONTROL
RS422/485
19200 baud, 8 bits, 1 stop no parity
Control from frame active front panel and remote panel
Statesman allows control from any PC on a network
SNMP monitoring and control available as a frame option
All functions available from Statesman. All main functions available from frame active front panel and remote panel
HD-AIP2 DUAL ANALOGUE AUDIO INPUT PIGGYBACK
AUDIO INPUTS
Two analogue stereo pairs or four mono channels. 24 bit quantising A to Ds. High input impedance (20 kohm) balanced
INPUT LEVEL RANGE
0dBFS = +28dBu max / 0dBFS = +12dBu min
Factory set default: 0dBFS = +18dBu or +24dBu by on board link
SIGNAL TO NOISE
99dB (+18dBu) rms., 22Hz to 22kHz typ.
TOTAL HARMONIC DISTORTION
0.004% THD+N rms., 22Hz to 22kHz typ.
INTERCHANNEL CROSSTALK
-110dB at 1kHz, -90dB at 20kHz, rms., typ.
HD-DIP2 AND HD-DIP2-RS DUAL DIGITAL AUDIO INPUT PIGGYBACKS
AUDIO INPUTS
Two 24 bit stereo pairs. AES3 110 ohm or HiZ (balanced) D-Type, or AES3-id (unbalanced) 75 ohm BNC. Set by on board jumper links
Synchronous audio to video 48kHz
Asynchronous audio to video 48kHz + or - 50ppm
HD-DIP2-RS is used for asynchronous AES inputs or AES at different sample rates (30kHz to 108kHz eg. 44.1kHz CD players or 96kHz DVD players)
TOTAL HARMONIC DISTORTION (DIP2-RS)
0.0002%
HD-AOP2 DUAL ANALOGUE AUDIO OUTPUT PIGGYBACK
AUDIO OUTPUTS
Two analogue stereo pairs or four mono channels. 24 bit quantising D to As. Low output impedance (66 ohm) balanced
INPUT LEVEL RANGE
0dBFS = +28dBu max / 0dBFS = +12dBu min
Factory set default: 0dBFS = +18dBu or +24dBu by on board link
SIGNAL TO NOISE
99dB (+18dBu) rms., 22Hz to 22kHz typ.
TOTAL HARMONIC DISTORTION
0.002% THD+N rms., 22Hz to 22kHz typ.
INTERCHANNEL CROSSTALK
-110dB at 1kHz, -90dB at 20kHz, rms., typ.
HD-DOP2-110 AND HD-DOP2-75 DUAL DIGITAL AUDIO OUTPUT PIGGYBACKS
AUDIO OUTPUTS
Two 20 bit AES/EBU stereo pairs
AES: HD-DOP2-110 110 ohm balanced D-Type or HD-DOP2-75 75 ohm unbalanced BNC
|
