Vision frame systemIntegrated fibre symbolSix framestore synchronisers symbolVideo over IP symbol3Gb/s symbolHD symbolSD symbolSix channel symbolRemote control symbolApp symbol

SDI6-IP-2110

What is it?

SDI6-IP-2110 IP gateway app

3G/HD/SD SDI to IP gateway app for SMPTE ST 2110.

Reason to choose it...

Supporting the full suite of SMPTE ST 2110 protocol standards, this feature-packed IP gateway includes full VLAN support, user-defined traffic shaping, discrete AES input, PTP synchronisation, ten frames of video delay, unicast and multicast transmission support, signal status monitoring and support for IS-04 and IS-05. Plus you can use it for as long as you need it – when this functionality is no longer required you can simply install a different low-cost app on your MARBLE-V1 hardware.

Ideal for...

Encapsulating any SDI feeds to SMPTE ST 2110 for transport of uncompressed video over 10GbE IP networks.

Got a question?

We would be very happy to answer any questions you've got about the SDI6-IP-2110. Either send us an e-mail or get an immediate response by speaking to us now on our Live Chat...

 
  • Main features
  • Details
  • Specs
  • What outputs do I get?
  • What do I order?

Main features

  • 3G/HD/SD SDI to IP gateway
  • Software app that runs on the MARBLE-V1 media processor
  • Encapsulates SDI to IP to allow signal transportation over 10GbE IP networks
  • Supports the SMPTE ST 2110 protocol suite of standards for essence-based output flows
  • Converts six HD/SD or three 3Gb/s SDI input connections and allows flexible assignment of the converted flows to either of the two output 10GbE links
  • Allows discrete AES input for SMPTE ST 2110-30 and ST 2110-31 encapsulation
  • Supports 31 SDI video standards
  • Full range of VLAN support
  • Unicast and multicast transmission support
  • PTP synchronisation, with support for master and secondary domain
  • Supports output flow types N, NL and Wide
  • Know your signal is present and valid, thanks to signal monitoring and fault detection
  • Inputs and outputs accessed by using an appropriate rear module (VR06)
  • Housed in Vision rack frames
  • Space-saving: MARBLE-V1 media processor is a ‘double slot’ 96mm x 325mm card, with up to ten MARBLE-V1 fitting in 3U
  • Supports IS-04 and IS-05
  • Flexible control and monitoring: frame integrated control panel, VisionPanel remote control panel, SBB-4 smart button box, SNMP, ASCII and JSON protocols or the web browser-based VisionWeb Control
  • Five year warranty (with product registration)

Details

Robust SDI to IP conversion

The SDI6-IP-2110 IP gateway encapsulates SDI to IP to allow the transport of uncompressed video over IP networks.

Supporting the SMPTE ST 2110 essence-based suite of protocols and 31 SDI video standards, the SDI6-IP-2110 app converts up to six HD/SD or three 3Gb/s SDI input connections for output over 10GbE IP network interfaces, with stream duplication ability for redundant output flows.

There is a choice of fibre modules for the fibre SFP+ 10GbE IP network interfaces: either 850nm multi-mode for up to 300m or 1310nm single-mode for up to 10km.

Features include full VLAN support with no restrictions and unicast and multicast transmission support. The output flow configuration is on a per flow basis, allowing for ultimate flexibility in network addressing.

It's a software app

App cloudThe future-proof SDI6-IP-2110 is a software app that runs on the MARBLE-V1 media processor – purpose-built video over IP hardware that fits in the Vision frames. Apps that are bought with the hardware can be replaced with different low-cost apps as needs change, helping you make the most of your budget. No other IP products make it quite so easy for your systems to grow and mature with the transition.

More about MARBLE-V1

Featuring a powerful CPU/GPU processor, the MARBLE-V1 media processor hardware has six bi-directional SDI connections, four 10GbE SFP+ network interface ports and eight bi-directional discrete AES stereo channels. The software app installed determines the functionality. App licences are tied to the MARBLE hardware and are for the life of the app until the owner releases or transfers a licence.

Dealing with the video, audio and data

Video, audio and data are de-embedded and routed to the appropriate SMPTE ST 2110 encapsulators.

To tell receivers how to interpret what is contained in each flow and set the correct video, audio and data parameters, all outgoing flows have an exposed Session Description Protocol (SDP) adhering to IETF RFC 4566. Every ST 2110 output flow created by the SDI6-IP-2110 app will have a signal defined SDP.

Video flows are encapsulated to ST 2110-20 specification. The app employs user definable traffic shaping in accordance with ST 2110-21. Output flows may be configured per flow to use N, NL or Wide, which allows these flows to be compliant in any media network.

Audio stream encapsulation is configured via a user matrix that allows for routing of de-embedded audio as well as external digital audio (via Crystal Vision’s DIOP8 audio piggyback) to AES67 output flows in accordance with ST 2110-30 standards. AES3 over IP is supported for non-PCM streams adhering to ST 2110-31.

Data encapsulation conforms to ST 2110-40 standards. Flow generated SDP will include line numbers and offsets, when possible, to assist receivers tasked with rebuilding SDI HANC and VANC to SMPTE ST 291 ancillary data standards.

Timing and delay

Output flows are RTP timestamped using system Precision Time Protocol (PTP), adhering to the ST 2110-10 standard. PTP timing is universal to all output flows. PTP redundancy is achieved by a system master/backup setup configuration.

The output flow timing can be fully adjusted with respect to the system PTP using three time-based controls (0 - 42ms adjustable in 0.1ms steps, 0 - 100us adjustable in 1us steps and 0 - 1us adjustable in 5ns steps).

An additional ten frames of delay (adjustable in one frame steps) allows compensation for any big system delays and can be configured individually for each output flow.

Flag up faulty signals

The SDI6-IP-2110 includes signal status monitoring for peace of mind. The status indications available are video present, video format, video black, video frozen, PTP master and backup clock present, audio groups present and Incoming AES 1-8 audio present, with the SDI6-IP-2110 able to provide warnings of any problems via SNMP traps.

The video black and video frozen parameters can be delayed by 2-60 seconds before an alarm is asserted to prevent false alarming during brief video pauses.

Flexible control

All control is done remotely. The remote control and monitoring options for the SDI6-IP-2110 app running on the MARBLE-V1 media processor include an integrated control panel on the Vision 3 frame, the VisionPanel remote control panel, the SBB-4 smart button box, SNMP and the VisionWeb web browser control. The SDI6-IP-2110 app will also support AMWA NMOS IS-04 for discovery and registration and IS-05 for device connection management.

Crystal Vision frameSave rack space

Fitting in the standard Vision frames (currently available in 3U size), MARBLE-V1 is a space-saving 96mm x 325mm card that sits in one frame slot – allowing up to ten media processors in 3U. The double slot VR06 frame rear modules is used to access the inputs and outputs on the SDI6-IP-2110 app.

 

Specs

SDI6-IP-2110 app running on MARBLE-V1 media processor...

MECHANICAL

‘Double slot’ Vision card 96mm x 303mm (96mm x 325mm including finger pull)

Weight: 355g

Power consumption: 25 Watts

VIDEO INPUTS

Three 3Gb/s SDI inputs or six HD or SD SDI inputs

If the input is 3Gb/s then inputs 1, 3 and 5 should be used and inputs 2, 4 and 6 should be disabled

Video inputs can be different standards but must be same frame rate

270Mb/s or 1.5Gb/s or 3Gb/s serial compliant to SMPTE 259, SMPTE 292-1 and SMPTE 424/425-A

The video formats supported are 625i, 525i, 720p50, 720p59.94, 720p60, 1080i50, 1080i59.94, 1080i60, 1080p23.98, 1080p24, 1080p25, 1080p29.97, 1080p30, 1080p50, 1080p59.94, 1080p60, 1080PsF23.98, 1080PsF24, 1080PsF25, 1080PsF29.97, 1080PsF30, 2048x1080p23.98*, 2048x1080p24*, 2048x1080p25*, 2048x1080p29.97*, 2048x1080p30*, 2048x1080PsF23.98*, 2048x1080PsF24*, 2048x1080PsF25*, 2048x1080PsF29.97*, 2048x1080PsF30* (*= YUV 4:2:2 10 bit)

3Gb/s cable equalisation up to 100m using Belden 1694A. HD cable equalisation up to 140m with Belden 1694A or equivalent (approx. 100m with Belden 8281). SD cable equalisation >250m Belden 8281 or equivalent

AUDIO INPUTS

1-8 AES via DIOP8 audio piggyback or embedded SDI audio

FLOW OUTPUTS

Two fibre SFP+ 10GbE IP network interfaces. Choice of fibre modules: either 850nm multi-mode (for up to 300m) or 1310nm single-mode (for up to 10km)

Protocols supported on network interfaces: SMPTE 2110-10, -20, -21, -30, -31, -40, -50, IGMPv3, ARP, ICMP ping, IPv4, IPv6 (future), IEEE802.1q, VLAN, IEEE802.3-2012 (10G Ethernet)

ST 2110-21 traffic shaping on output flows may be configured per flow to use N, NL or Wide

Any IP output can be assigned to either of two 10GbE IP network interfaces. Typical use might have the second 10GbE IP network interface used as the protected output for link redundancy, which protects the stream from lost packets by creating two streams of the same data using different routing to the destination Alternatively, it is possible to have a unicast on one 10GbE interface and a multicast on the other

The video loss controls allow the user to select what will happen to an output flow in the event that the input is lost. The user can specify to freeze the last good frame or show a black or blue screen or 100% colour bars (with or without an initial delay of three seconds). No output can also be selected. This is independently adjustable on each output flow

The test pattern controls allow the user to override an input and force the output flow to output colour bars, blue or black or freeze the picture – useful during installation when input signals may not yet be applied

SDI to ST 2110 IP encapsulator, encapsulates SDI to IP to allow for signal transportation over 10GbE IP networks

Each encapsulated output flow will contain a signal defined Session Description Protocol detailing the parameters of the flow

Any output flow can be routed to either network

TIMING AND SYNCHRONISATION

Output flows are timestamped using master or backup system PTP

PTP timing is universal to all output flows

PTP is via 10GbE network connection

PTP redundancy is achieved by system master/backup setup configuration

PTP health is monitored and can be used to raise SNMP alarm

Output flow timing can be fully adjusted with respect to the system PTP using time based controls: 0 - 42ms adjustable in 0.1ms steps, 0 - 100us adjustable in 1us steps and 0 - 1us adjustable in 5ns steps

An additional ten frames of video delay (adjustable in one frame steps) allows compensation for any big system delays. This delay can be configured individually for each output flow

DELAY THROUGH CARD

Minimum delay: TBD

LED INDICATION OF:

Power okay

SIGNAL MONITORING

Checks can be performed on the following video and audio parameters, with faults provided via SNMP traps and VisionWeb signal status:

  • Video present
  • Video format
  • Video black
  • Video frozen
  • PTP master and backup clock present
  • Audio group 1 present
  • Audio group 2 present
  • Audio group 3 present
  • Audio group 4 present
  • Incoming AES 1-8 audio present

The video black and video frozen parameters can be delayed by 2-60 seconds before an alarm is asserted to prevent false alarming during brief video pauses

CONTROL

Supports IS-04 and IS-05

VisionWeb Control is available via the web server on the frame and allows control and monitoring using a standard web browser on a computer, tablet or phone

Control from integrated control panel on Vision 3 frame and remote panel

SBB-4 smart button box connects to the frame via Ethernet and provides four programmable LCD switches. The SBB-4 uses information from VisionWeb for settings. The four switches will be configured for each order to provide the controls required. Uses Power over Ethernet so must be used with PoE enabled switch

SNMP monitoring and control available as standard

Control using ASCII and JSON protocols

LICENSING

Licences for an app are tied to the installed MARBLE hardware

A licence is for the life of the product until the owner releases or transfers a licence

New licences will be provided with new apps purchased for existing MARBLE hardware

 

What outputs do I get?

Signal inputs and outputs are accessed by using an appropriate rear module.

The Vision rear modules slot on at the back of the frame and typically feature BNC, Micro BNC, D-Type and LC fibre connectors.

There is one rear module available for the SDI6-IP-2110...

VR06 rear module label and connections

More about the VR06

Connectors: 6 BNCs, 1 D-Type and 2 dual LC fibre

Frame slots used: 2

Boards in 3U: 10

Why use it: It's the only rear module for the SDI6-IP-2110

Also used for: SDI6-IP-2022, IP-SDI6-2022 and IP-SDI6-2110

 

SDI6-IP-2110 inputs and outputs with VR06 rear module

VR06 rear module label for SDI6-IP-2110

 

For more visual technical information, download the SDI6-IP-2110 block diagram.

What do I order?

Request a quote...

Read the ordering info below then fill in this form to request a quote for the SDI6-IP-2110 IP gateway and accessories...

Your contact details
Items for quote

First you need the software app...

SDI6-IP-2110
IP gateway which supports SMPTE ST 2110 essence-based suite of standards. Up to six HD/SD or three 3Gb/s SDI input connections converted to two output 10GbE IP network interfaces. Software app which runs on the MARBLE-V1 media processor

Now choose your media processor hardware and SFP+ modules...

MARBLE-V1
Media processor hardware which runs Crystal Visionís software apps. Housed in the Vision frames, with up to ten MARBLE-V1 in 3U. Requires two 850nm or 1310nm SFP+ transceiver modules when used with SDI6-IP-2110 app
SFP+10G-850MM
Multi-mode 850nm 10GbE SFP+ transceiver module for MARBLE-V1 media processor – two required when used with SDI6-IP-2110 app
SFP+10G-1310SM
Single-mode 1310nm 10GbE SFP+ transceiver module for MARBLE-V1 media processor – two required when used with SDI6-IP-2110 app

Select the DIOP8 audio piggyback if you want to input external digital audio...

DIOP8
Digital audio input or output piggyback. One DIOP8 can be fitted to the MARBLE-V1 hardware for eight stereo pairs

Next select your frame...

Vision 3
3U frame with integrated control panel and smart CPU for up to 20 Crystal Vision cards from the Vision range. Includes two PSU3-VF power supplies for redundancy. Allows Ethernet connection to a PC

You need a rear module to access your inputs and outputs...

VR06
Two slot frame rear module. Allows ten SDI6-IP-2110 in 3U. Gives access to six HD/SD or three 3Gb/s input connections, two 10GbE IP output network interfaces and all audio inputs

Next - control. Use the frame's integrated control panel, the VisionWeb web browser control or SNMP (both included in the frame for free), or alternatively order one of the items below...

VisionPanel
3U Ethernet remote control panel with touch screen
SBB-4
Smart button box with four programmable LCD switches. It is powered by PoE (Power over Ethernet) and therefore needs to be connected to a PoE enabled switch

Finally - extended support if required...

App support
Purchase with SDI6-IP-2110 app to get software upgrades for changes in
standards, new features and bug fixes – costs 20% of app list price per year
(with support for the first year included for free)

 

 

Do more...

 

Explore more...

Video over IP

From the Vision frame system...

  • MARBLE-V1 media processor hardware which runs Crystal Vision's software apps
  • SDI6-IP-2022 3G/HD/SD SDI to IP gateway app for SMPTE ST 2022
  • IP-SDI6-2022 IP to 3G/HD/SD SDI gateway app for SMPTE ST 2022
  • IP-SDI6-2110 IP to 3G/HD/SD SDI gateway app for SMPTE 2110
  • IP-IP-2022 IP to IP translator app for SMPTE 2022
  • IP-IP-2110 IP to IP translator app for SMPTE 2110 and SMPTE 2022